Glowshift Fuel Level Gauge Instrukcja Użytkownika Pobierz pdf

Elite 10 Color Fuel Level Gauge

For Product Numbers: GS-ET15 & GS-EWT15

Wire Harness Color Code

Red:

12v Constant (un-switched) Source (+)

Black:

Vehicle / Engine Ground (-)

White:

12v Ignition (switched) Source (+)

Orange:

12v Dimmer (switched) Source (+) (optional)

1. Disconnect the negative battery cable.

2. Connect the white sensor wire to the back of the gauge (port D) and

run it through the firewall to the vehicle’s fuel level sensor.

 Note: Be sure to use a grommet when routing the wires

through the firewall to protect them from stripping and

damage.

3. Use the Fuel Level Sensor Sensitivity Switch on the back of the gauge

to set the correct ohm (Ω) value scale to match the rating of the vehicle’s

fuel level sensor. Use the chart below to reference the correct setting that

applies closest to the values of your sensor. Please verify settings with a

repair manual or a dealer before installation.

 If you need to change the ohm selection, you must remove

power from the gauge, make your selection, and then reapply

power to the gauge for proper calibration.

 Be sure that your factory fuel level sensor is properly

grounded. You may have to add a secondary ground to

ensure it is properly grounded.

“Empty”

Ohm

Value

“Full”

Ohm

Value

Switch #

N/A

73 Ω

10 Ω

16 Ω

158 Ω

0 Ω

30 Ω

0 Ω

90 Ω

240 Ω

33 Ω

107.5 Ω

7 Ω

131 Ω

12 Ω

0 Ω

120 Ω

10 Ω

180 Ω

4. Connect the white wire to a positive 12 volt ignition (switched) source.

It may be connected to the fuse panel, an accessory wire, or any positive

12 volt source that turns on and off with the ignition switch of the vehicle.

 Note: If wiring to an un-fused source, install a 3 amp fuse inline

within 20 inches of the sources connection. You may obtain an

optional “expandable circuit” accessory. This component easily

fits into your fuse panel and provides an additional fused power

wire for accessories such as gauges. This is available at

GlowShift.com or a local auto parts store.

5. Connect the red wire to a positive 12 volt constant (un-switched)

source, either directly to the battery or to a fuse panel on the vehicle.

 Note: If wiring to an un-fused source, install a 3 amp fuse inline

within 20 inches of the sources connection. You may obtain an

optional “expandable circuit” accessory. This component easily

fits into your fuse panel and provides an additional fused power

wire for accessories such as gauges. This is available at

GlowShift.com or a local auto parts store.

6. The Night Time Dimming feature decreases the brightness of the gauge

face by 30%. Connect the orange wire to the 12 volt positive headlamp

source. This allows the mode to be activated when the headlights come on.

This step is optional and will not affect operation of the gauge if it is

omitted.

 Note: Do not connect the orange wire to a dimmer wheel.

This will cause the gauge lighting to flicker.

7. Connect the black wire from the gauge, to any good (unpainted) ground

connection. You may also route a wire directly to the negative side of the

vehicle’s battery.

8. Reconnect the negative battery cable.

9. Daisy Chain Feature (Optional): If you are installing more than one

Elite 10 Color Gauge, you can use the daisy chain feature to power up to 4

additional gauges. Simply plug the included daisy chain wire into the

gauge that is already powered (port B); then plug the other end of the wire

into the daisy chain port on the next gauge.

1 2 3

Operating Instructions 2

Podsumowanie treści

Strona 1

Elite 10 Color Fuel Level Gauge For Product Numbers: GS-ET15 & GS-EWT15 Wire Harness Color Code Red: 12v Constant (un-switched) Source (+) Bla

Strona 2 - Operating Instructions

Operating Instructions 1. 10-Color Mode: 1. Press the COLOR button to cycle between the 10 different color options. 2. The sequence of display c

Strona 3

ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER GlowShift Gauges, LLC ("GlowShift") warrants to the original retail consumer

Komentarze do niniejszej Instrukcji

Brak uwag

Glowshift Fuel Level Gauge Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Akcesoria do wody Glowshift Fuel Level Gauge. GlowShift Fuel Level Gauge User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Akcesoria do wody Glowshift Fuel Level Gauge