Glowshift Nitrous Pressure Gauge Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Akcesoria do wody Glowshift Nitrous Pressure Gauge. GlowShift Nitrous Pressure Gauge User Manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
  • Strona
    / 3
  • Spis treści
  • BOOKMARKI
  • Oceniono. / 5. Na podstawie oceny klientów
Przeglądanie stron 0
Elite 10 Color Nitrous Pressure Gauge
For Product Numbers: GS-ET14 & GS-EWT14
Wire Harness Color Code
Red:
12v Constant (un-switched) Source (+)
Black:
Vehicle / Engine Ground (-)
White:
12v Ignition (switched) Source (+)
Orange:
12v Dimmer (switched) Source (+) (optional)
1. Disconnect the negative battery cable.
2. Connect the supplied 1/8
th
- 27 NPT Nitrous Pressure Sensor to
the correct Nitrous Oxide System Pressure monitoring port.
In some cases, additional adapters or fittings may be
necessary for correct installation. Consult the
owner’s manual or contact the manufacturer of
your nitrous oxide system for proper installation
procedures and components.
3. Route the pressure sensor wire harness from the back of the
gauge (port D) through the firewall to the engine bay. Next,
couple and secure the sensor wire harness to the back of the
nitrous pressure sensor.
Note: Be sure to use a grommet when routing wires
through the firewall to protect them from stripping and
damage.
4. Connect the white wire to a positive 12 volt ignition (switched)
source. It may be connected to the fuse panel, an accessory wire,
or any positive 12 volt source that turns on and off with the
ignition switch of the vehicle.
Note: If wiring to an un-fused source, install a 3 amp
fuse inline within 20 inches of the sources connection.
You may obtain an optional “expandable circuit”
accessory. This component easily fits into your fuse
panel and provides an additional fused power wire for
accessories such as gauges. This is available at
GlowShift.com or a local auto parts store.
5. Connect the red wire to a positive 12 volt constant (un-switched)
source, either directly to the battery or to a fuse panel on the vehicle.
Note: If wiring to an un-fused source, install a 3 amp fuse
inline within 20 inches of the sources connection. You may
obtain an optional “expandable circuit” accessory. This
component easily fits into your fuse panel and provides an
additional fused power wire for accessories such as gauges.
This is available at GlowShift.com or a local auto parts
store.
6. The Night Time Dimming feature decreases the brightness of the
gauge face by 30%. Connect the orange wire to the 12 volt positive
headlamp source. This allows the mode to be activated when the
headlights come on. This step is optional and will not affect
operation of the gauge if it is omitted.
Note: Do not connect the orange wire to a dimmer
wheel. This will cause the gauge lighting to flicker.
7. Connect the black wire from the gauge, to any good (unpainted)
ground connection. You may also route a wire directly to the
negative side of the vehicle’s battery.
8. Reconnect the negative battery cable.
9. Daisy Chain Feature (Optional): If you are installing more
than one Elite 10 Color Gauge, you can use the daisy chain feature
to power up to 4 additional gauges. Simply plug the included daisy
chain wire into the gauge that is already powered (port B); then
plug the other end of the wire into the daisy chain port on the next
gauge.
Przeglądanie stron 0
1 2 3

Podsumowanie treści

Strona 1

Elite 10 Color Nitrous Pressure Gauge For Product Numbers: GS-ET14 & GS-EWT14 Wire Harness Color Code Red: 12v Constant (un-switched) Source (

Strona 2 - Operating Instructions

Operating Instructions 1. 10-Color Mode: 1. Press the COLOR button to cycle between the 10 different color options. 2. The sequence of display c

Strona 3

ONE YEAR NON-TRANSFERRABLE LIMITED WARRANTY AND DISCLAIMER GlowShift Gauges, LLC ("GlowShift") warrants to the original retail consumer

Komentarze do niniejszej Instrukcji

Brak uwag